All articles
CommercialBuyer GuideEngineering DrawingsTolerancesRFQ

Why Your 3D Printing Shop Asks for a 2D Drawing

3D Prototyping Hub·
Why Your 3D Printing Shop Asks for a 2D Drawing

You sent a clean STEP file, the geometry is watertight, and the reply came back asking for a drawing. It reads like bureaucracy — the shop already has the shape, in three dimensions, to six decimal places. A 3D printing shop asking for a 2D drawing is not asking for the shape. It is asking which parts of that shape are allowed to move, because the model does not say, and somebody has to decide before the part is made rather than after it arrives. If you are still choosing who to send the package to, browse the 3D printing provider directory and check what each shop says about inspection and tolerances first.

The Model Says What. The Drawing Says Which Features Matter.

A solid model is a statement of nominal geometry. Every dimension in it is exact and every dimension in it is equally exact, which is the problem: the 12.00 mm bore that has to accept a bearing and the 80.00 mm overall length that nobody will ever measure look identical in the file.

No process prints to nominal. Parts come off a machine somewhere inside a range, and the shop's job is to decide which range. Given only a model, it has two choices, and both cost you something:

  • Apply the house general tolerance to everything. Cheapest to quote, and the bearing bore comes back at whatever the process happened to give it.
  • Treat the whole part as critical. Tighter orientation, slower settings, an inspection step, possibly machining after printing — and a quote that may be double what the part needed.

A drawing collapses that choice. Two toleranced features and a note saying the rest is nominal tells the shop exactly where to spend money and where not to.

Carried by the 3D model Carried only by the drawing
Nominal shape and size Which dimensions are critical, and their limits
Feature positions relative to each other The datum everything is measured from
A hole's diameter and depth Whether that hole is tapped, reamed or takes a heat-set insert
Surface geometry Which face is cosmetic and which may carry support marks
Units, if the format declares them Material by grade, finish level, quantity
The current state of the file Part number and revision — what you are reordering

Read the right column as a list of decisions. Every one of them gets made whether or not you make it. The only question is whether you make it, or a scheduler you have never spoken to makes it at 7am to keep a machine loaded.

The Five Things a Drawing Settles

1. Where to measure from. "The hole is 0.3 mm out" is meaningless until you both agree what it is 0.3 mm out from. A datum — a face, an edge, a bore axis — turns a vague complaint into a measurement either party can repeat. This single callout resolves more disputes than tolerance values do, because most "wrong" parts are correct from one origin and wrong from another.

2. What has to fit, and how tightly. Commonly published bureau tolerances run around ±0.5% with a floor near ±0.5 mm for FDM, and roughly ±0.2% with a floor near ±0.1–0.2 mm for resin-based processes; the specifics vary by shop, machine and material, which is exactly why they are published per-shop. Our breakdown of tolerances and accuracy in 3D printing covers what each process genuinely holds. Your drawing's job is narrower: name the two or three features that must land, and let the shop apply its general tolerance to the rest.

3. What happens to the holes. A 5 mm hole in the model might need to come out as a tapped M6, a reamed bore, or a pocket for a heat-set insert. Those are three different operations and three different as-printed diameters. The model shows one cylinder for all three.

4. Which face the customer sees. Every part has an orientation that is cheapest to print and an orientation that puts the support witness marks somewhere you do not mind. Mark the cosmetic face and the shop will plan around it. Leave it unmarked and the scar lands where the slicer put it, which is usually the largest flat surface — the one you were going to photograph.

5. Which version this is. A part number and a revision letter in the title block is what makes a second order match the first. Filenames do not do this; the reasons a reorder comes back different from the first batch are mostly reasons nobody could prove which revision was approved.

Does It Actually Need Drying?

Tell moisture from the faults that imitate it. Then dry it without wrecking it.

The file downloads on this page as soon as you submit. No waiting on an email.

What Happens With No Drawing at All

The failure is quiet, which is what makes it expensive. The shop does not stop and ask — a bare model is a complete, quotable, printable job, so it gets quoted, printed and shipped against defaults. Then the parts arrive and the conversation starts.

At that point there is no document to appeal to. The shop built the geometry you sent, to its published general tolerance, in a legal orientation. Nothing was violated because nothing was specified. That is the structural reason a remake request without a drawing turns into a negotiation rather than a warranty claim — the same dynamic behind most of the cases in why 3D printing orders come back wrong.

The STL case is worse again. STL files carry no unit declaration, so a model exported in inches and read as millimetres is scaled by 25.4 with no error anywhere in the chain. A drawing with a dimension on it catches that before the machine runs. A file alone cannot.

The Twenty-Minute Drawing

You are not producing a controlled document. You are producing the page the shop prints and sets next to the part. That page needs:

  1. One or two views — whatever shows the features you care about. Isometric plus a front view is usually enough.
  2. A datum, even if it is just a note: "all dimensions from the mounting face."
  3. Two or three toleranced dimensions, each with a word about what it mates with. "⌀12.00 +0.05/−0.00 — press fit, 6001 bearing" tells the shop more than the number alone.
  4. A general note — "all other dimensions nominal, standard tolerance acceptable." This is the line that keeps the quote down.
  5. Thread, insert and post-machining callouts on the features that need them.
  6. A title block: part number, revision, material and grade, finish, quantity, units, date, your name.

Export it as a PDF and send it with the STEP file. If drafting is genuinely not available to you, an annotated screenshot with three arrows and the same six pieces of information does most of the work for a prototype — send it as an attachment rather than as body text, so it survives the handoff from sales to the floor. The rest of the package is covered in how to prepare your files for a 3D printing quote.

When You Genuinely Do Not Need One

Not every job deserves a drawing, and shops do not want one for every job either.

  • Display, cosmetic and concept models. Nothing fits anything. Say so explicitly — "visual model, no critical dimensions" — and you have told the shop to optimise for finish and price.
  • Fit-check iterations. When you are printing a part specifically to find out whether it fits, the measurement happens on your desk, not theirs.
  • Parts where the file is the authority. Organic, scanned or generatively designed geometry sometimes has no dimensionable features worth calling out. The honest version is a note saying as much, plus the one or two interfaces that do matter.

Even in these cases, write the title block line: material, finish, quantity, revision. That is thirty seconds and it is the part that makes a reorder possible.

What a Good Shop Does With It

A shop that asks for a drawing is telling you it intends to measure something, which is a better sign than one that never asks. When the drawing arrives, it drives the quote — orientation planned around the cosmetic face and the critical bore, a secondary operation priced in where the tolerance demands one — and then it drives acceptance. The toleranced features become the inspection list, the datum becomes the setup, and the report that ships with the parts refers to your numbers rather than the shop's.

For parts where the inspection matters more than the printing, that measurement step can be a service in its own right; see 3D scanning services for quality inspection for when full-part dimensional capture is worth paying for.

Ready to send the package out? Find 3D printing providers in the directory, filter by process and location, and send the drawing with the model to two shops that match the job rather than the file alone to ten that do not.


Hero photograph by Greg Rosenke (Unsplash).

Does It Actually Need Drying?

Tell moisture from the faults that imitate it. Then dry it without wrecking it.

The file downloads on this page as soon as you submit. No waiting on an email.

Frequently Asked Questions

Ready to find a 3D printing service provider?

Browse 2,000+ verified providers across the United States and submit your quote request free.

Browse Providers